LCDproc development and user support list

Text archives Help


[Lcdproc] Trying to get a new 633 USB working on RH9


Chronological Thread 
  • From: BGentry AT ncst.com (Brian Gentry)
  • Subject: [Lcdproc] Trying to get a new 633 USB working on RH9
  • Date: Fri Jul 25 15:31:01 2003

Christopher,
I got it working... My mistake was hitting <enter> on the YES to exit
menuconfig... Duh.. I should have hit "y".. My only excuse was it was
late ... 3:30am...=20

Thanks for all your help..



-----Original Message-----
From: Christopher Lyon
[mailto:cslyon AT netsvcs.com]=20
Sent: Friday, July 25, 2003 11:25 AM
To: Goetz Bock;
lcdproc AT lists.omnipotent.net
Subject: RE: [Lcdproc] Trying to get a new 633 USB working on RH9


> -----Original Message-----
> From: Goetz Bock
> [mailto:bock AT blacknet.de]
> Sent: Friday, July 25, 2003 2:41 AM
> To:
> lcdproc AT lists.omnipotent.net
> Subject: Re: [Lcdproc] Trying to get a new 633 USB working on RH9
>=20
>=20
> On Thu, Jul 24 '03 at 15:51, Christopher Lyon wrote:
> [ ... ]
> > 'make menuconfig' - just open and save. Unless you want to get
tricky
> > and make some mods.
> use 'make oldconfig' if you don't want to change anything

This just replaces the .config file with the .config.old. Right?

>=20
> > 'make dep' - setups up the dependancies
> >
> > 'make -j2 bzImage' - that creates the image for grub loader (NOTE
LILO
> > is a different command)
> the command for lilo is the same, actuallt it is independend of the
used
> bootloader. It just created the kernel binary (, as a Big Zipped
Image)
>=20
> > 'make modules' - makes the module files
> > 'make modules_install' - installs the modules files
> > 'make install' - installs the new kernel
> >
> > 4. Check your /boot/grub/grub.conf file to make sure the kernel and=20
> > settings are in there. You should see a kernel-2.4.20-18.9.custom in

> > there.
> Here you would have to make sure that /etc/lilo.conf is correct (e.g.=20
> includes the new kernel), and run lilo afterwards (as root)
>=20
> > Notes just as an FYI:
> > make mrproper - cleans everything even the .config
> > make clean - just cleans the object and other complied files
> If you just add or remove options, or change a driver, a make clean=20
> should be sufficient.
> --
> /"\ Goetz Bock at blacknet dot de -- secure mobile Linux everNETting
> \ / (c) 2003 as GNU FDL 1.1
> X [ 1. Use descriptive subjects - 2. Edit a reply for brevity - ]
> / \ [ 3. Reply to the list - 4. Read the archive *before* you post ]=20
> _______________________________________________
> LCDproc mailing list
> LCDproc AT lists.omnipotent.net=20
> http://lists.omnipotent.net/mailman/listinfo/lcdproc

_______________________________________________
LCDproc mailing list
LCDproc AT lists.omnipotent.net
http://lists.omnipotent.net/mailman/listinfo/lcdproc




Archive powered by MHonArc 2.6.18.

Top of page